View ECG055_191115.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ECG055
Product Features
x DC - 3 GHz x +18 dBm P1dB at 1 GHz x +34 dBm OIP3 at 1 GHz x 20 dB Gain at 1 GHz
The Communications Edge TM Product Information
InGaP HBT Gain Block
Product Description
The ECG055 is a general-purpose buffer amplifier that offers high dynamic range in a low-cost surface-mount package. At 1000 MHz, the ECG055 typically provides 20 dB of gain, +34 dBm Output IP3, and +18 dBm P1dB. The ECG055 consists of Darlington pair amplifiers using the high reliability InGaP/GaAs HBT process technology and only requires DC-blocking capacitors, a bias resistor, and an inductive RF choke for operation. The device is ideal for wireless applications and is available in lowcost, surface-mountable plastic SOT-86 and SOT-89 packages. The ECG055 is also available in a leadfree/green/RoHS-compliant SOT-89 package. All devices are 100% RF and DC tested. The broadband MMIC amplifier can be directly applied to various current and next generation wireless technologies such as GPRS, GSM, CDMA, and WCDMA. In addition, the ECG055 will work for other various applications within the DC to 3 GHz frequency range such as CATV and fixed wireless.
Functional Diagram
GND 4
x 4.3 dB Noise Figure at 2 GHz
x Available in SOT-86, SOT-89 89 and lead-free / green SOT-89 Package Styles x Internally matched to 50 :
1 RF IN
2 GND
3 RF OUT
ECG055B / ECG055B-G
GND
4
Applications
x x x x x x Mobile Infrastructure CATV / DBS W-LAN / ISM RFID Defense / Homeland Security Fixed Wireless
RF In
1
3 RF Out
2
GND
ECG055C
Specifications (1)
Parameter
Operational Bandwidth Test Frequency Gain Output P1dB Output IP3 (2) Test Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 (2) Noise Figure Device Voltage Device Current
Typical Performance (3)
Units
MHz MHz dB dBm dBm MHz dB dB dB dBm dBm dB V mA
Min
DC
Typ
1000 19.7 +18 +34 2000 19 20 20.8 +18 +32 4.3 4.8 65
Max
3000
Parameter
Frequency S21 S11 S22 Output P1dB Output IP3 Noise Figure
Units
MHz dB dB dB dBm dBm dB 500 20 -30 -23 +18 +34 4.6
Typical
900 19.7 -27 -23 +18 +34 4.5 1900 19 -22 -21 +18.2 +32 4.3

2140 18.5 -20 -15 +19.0 +30.5 3.8
System.
3. Test conditions: T = 25 C, Supply Voltage = +6 V, Device Voltage = +5.0V, Rbias = 18 , 50
4.2
5.3

1. Test conditions unless otherwise noted: 25 C, Supply Voltage = +6 V, Rbias = 18 , 50 System. 2. 3OIP measured with two tones at an output power of +4 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
Absolute Maximum Rating
Parameter
Operating Case Temperature Storage Temperature RF Input Power (continuous) Device Current Junction Temperature -40 to +85 qC -65 to +150 qC +12 dBm 150 mA +250 qC
Ordering Information
Part No.
ECG055B ECG055B-G ECG055C ECG055B-PCB ECG055C-PCB
Description
(leaded SOT-89 Pkg)
Rating
InGaP HBT Gain Block InGaP HBT Gain Block
(lead-free/green/RoHS-compliant SOT-89 Pkg)
InGaP HBT Gain Block (SOT-86 Pkg) 700 -2400 MHz Fully Assembled Eval. Board 700 -2400 MHz Fully Assembled Eval. Board
Specifications and information are subject to change without notice
Operation of this device above any of these parameters may cause permanent damage.

WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
December 2004
ECG055
Frequency S21 S11 S22 Output P1dB Output IP3 Noise Figure
The Communications Edge TM Product Information
InGaP HBT Gain Block
Typical Device RF Performance
Supply Bias = +6 V, Rbias = 18 :, Icc = 65 mA
100 20.2 -36 -23 +18.2 +33 3.4 500 20.1 -30 -23 +18 +33.5 4.6
MHz dB dB dB dBm dBm dB
900 19.7 -27 -23 +18.1 +34.5 4.5
1900 18.5 -22 -21 +18.2 +33.5 4.3
2140 18.2 -22 -20 +17.8 +32.9 4.2
2400 17.8 -22 -20 +17.8 +32 4.2
3500 16.2 -24 -17 +17.2
5800 14 -21 -11
1. Test conditions: T = 25 C, Supply Voltage = +6 V, Device Voltage = 4.8 V, Rbias = 18 , Icc = 65 mA typical, 50 System. 2. 3OIP measured with two tones at an output power of +4 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3. Data is shown as device performance only. Actual implementation for the desired frequency band will be determined by external components shown in the application circuit.
Gain vs. Frequency 25 20 S11, S22 (dB) S21(dB) 15 10 5 0 0 1 2 3 4 Frequency (GHz) OIP3 vs. Frequency 40 35 OIP3 (dBm) NF (dB) 30 25 20
1
S11, S22 vs. Frequency 0 -5 Icc -10 -15 -20 -25 5 6 0 1 2 3 4 Frequency (GHz) 5 6 S11 S22
160 140 120 100 80 60 40 20 0 0.0 1.0
Icc vs. Vde
2.0
3.0 Vcc
4.0
5.0
6.0
Noise Figure vs. Frequency 6 5 4 3 P1dB (dBm) 18 20
P1dB vs. Frequency
16 25 C 1 -40 C 85 C 4
25 C
-40 C
85 C
4
2 3 Frequency (MHz)
2 500
1000
1500
2000
2500
3000
14
Frequency (MHz)
2 3 Frequency (MHz)
Specifications and information are subject to change without notice

WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
December 2004
ECG055
The Communications Edge TM Product Information
InGaP HBT Gain Block
Recommended Application Circuit
Vcc Icc = 65 mA
R4 Bias Resistor C4 Bypass Capacitor C3 0.018 F L1 RF Choke RF IN ECG055 C1 Blocking Capacitor C2 Blocking Capacitor RF OUT
ECG055B-PCB
ECG055C-PCB
Reference Designator L1 C1, C2, C4
50 820 nH .018 F
Recommended Component Values Frequency (MHz) 500 900 1900 2200 220 nH 68 nH 27 nH 22 nH 1000 pF 100 pF 68 pF 68 pF
2500 18 nH 56 pF
3500 15 nH 39 pF
1. The proper values for the components are dependent upon the intended frequency of operation. 2. The following values are contained on the evaluation board to achieve optimal broadband performance:
Ref. Desig. L1 C1, C2 C3 C4 R4
Value / Type 39 nH wirewound inductor 56 pF chip capacitor 0.018 PF chip capacitor Do Not Place 18 : 1% tolerance
Size 0603 0603 0603 0805
Recommended Bias Resistor Values Supply R1 value Size Voltage 6V 18.5 ohms 0805 7V 33.8 ohms 1210 8V 49 ohms 1210 9V 65 ohms 2010 10 V 80 ohms 2010 12 V 111 ohms 2512
The proper value for R1 is dependent upon the supply voltage and allows for bias stability over temperature. WJ recommends a minimum supply bias of +6 V. A 1% tolerance resistor is recommended.
Specifications and information are subject to change without notice

WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
December 2004
ECG055
The Communications Edge TM Product Information
InGaP HBT Gain Block
ECG055B (SOT-89 Package) Mechanical Information
This package may contain lead-bearing materials. The plating material on the leads is SnPb.
Outline Drawing
Product Marking
The component will be marked with an "E055" designator with an alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part are located on the website in the "Application Notes" section.
MSL / ESD Rating
ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114
MSL Rating: Level 3 at +235 C convection reflow Standard: JEDEC Standard J-STD-020
Mounting Config. Notes Land Pattern
1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135" ) diameter drill and have a final plated thru diameter of .25 mm (.010" ). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees.
Specifications and information are subject to change without notice

WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
December 2004
ECG055
The Communications Edge TM Product Information
InGaP HBT Gain Block
This package is lead-free/Green/RoHS-compliant. It is compatible with both lead-free (maximum 260qC reflow temperature) and leaded (maximum 245qC reflow temperature) soldering processes. The plating material on the leads is NiPdAu.
ECG055B-G (Green / Lead-free SOT-89 Package) Mechanical Information
Outline Drawing
Product Marking
The component will be marked with an " E055G" designator with an alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part are located on the website in the " Application Notes" section.
MSL / ESD Rating
ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114
Land Pattern
MSL Rating: Level 3 at +260 C convection reflow Standard: JEDEC Standard J-STD-020
Mounting Config. Notes
1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135" ) diameter drill and have a final plated thru diameter of .25 mm (.010" ). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees.
Specifications and information are subject to change without notice

WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
December 2004
ECG055
The Communications Edge TM Product Information
InGaP HBT Gain Block
ECG055C (SOT-86 Package) Mechanical Information Outline Drawing Product Marking
The component will be marked with a twodigit numeric lot code followed by a " Y" designator on the top surface of the package. Tape and reel specifications for this part are located on the website in the " Application Notes" section.
MSL / ESD Rating
ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114
MSL Rating: Level 1 at +235 C convection reflow Standard: JEDEC Standard J-STD-020
Mounting Config. Notes Land Pattern
1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135" ) diameter drill and have a final plated thru diameter of .25 mm (.010" ). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees.
Specifications and information are subject to change without notice

WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
December 2004
ECG055
Freq (MHz) S11 (dB)
The Communications Edge TM Product Information
InGaP HBT Gain Block
Typical Device S-Parameters - ECG055B / ECG055B-G
S-Parameters (Vdevice = +4.8 V, ICC = 65 mA, T = 25 C, calibrated to device leads)
S11 (ang) S21 (dB)
50 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000
-43.39 -35.69 -36.17 -39.67 -47.76 -34.49 -27.47 -22.05 -17.95 -14.46 -11.17 -8.90 -6.98
36.98 21.69 9.50 -13.97 -168.22 149.36 131.16 110.28 92.80 78.77 65.64 51.85 40.70
20.59 20.33 19.97 19.43 18.94 18.33 17.71 17.12 16.51 15.85 15.20 14.33 13.37
Typical Device S-Parameters - ECG055C
S-Parameters (Vdevice = +4.8 V, ICC = 65 mA, T = 25 C, calibrated to device leads)
Freq (MHz) S11 (dB) S11 (ang) S21 (dB)
50 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000
-38.17 -30.35 -26.51 -23.32 -22.01 -21.87 -21.62 -23.63 -26.77 -31.76 -32.57 -24.49 -18.97
9.34 38.64 30.55 16.54 8.06 -3.80 -11.61 -13.22 -23.25 -20.76 122.50 133.61 125.72
20.30 20.11 19.67 19.00 18.39 17.62 16.91 16.27 15.65 15.09 14.65 14.16 13.73

WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621

S21 (ang)
S12 (dB)
S12 (ang)
S22 (dB)
S22 (ang)
177.68 157.95 136.78 116.67 97.59 78.63 60.90 43.22 25.75 8.27 -9.36 -27.36 -44.65
-22.62 -22.54 -22.43 -22.21 -21.89 -21.57 -21.15 -20.74 -20.33 -19.98 -19.77 -19.71 -19.82
-0.53 -3.66 -7.11 -10.88 -14.89 -19.36 -24.45 -30.55 -37.20 -44.69 -53.40 -62.31 -71.82
-24.22 -22.15 -19.38 -16.82 -14.74 -13.12 -11.44 -10.09 -8.35 -6.89 -5.48 -4.20 -3.18
-3.40 -55.60 -94.63 -124.20 -149.72 -171.09 168.48 149.65 131.32 113.94 97.62 81.72 66.66
S21 (ang)
S12 (dB)
S12 (ang)
S22 (dB)
S22 (ang)
178.31 161.09 143.04 126.43 111.18 96.71 83.83 71.31 59.48 47.94 36.34 24.39 13.11
-22.39 -22.33 -22.23 -22.09 -21.81 -21.55 -21.16 -20.78 -20.29 -19.79 -19.25 -18.78 -18.29
0.12 0.74 1.87 2.57 3.37 3.41 3.82 3.21 2.65 1.21 -0.79 -3.46 -6.40
-22.58 -23.00 -22.48 -21.21 -20.79 -19.71 -18.27 -17.28 -15.32 -14.24 -12.75 -11.56 -10.39
-1.41 -29.41 -50.33 -77.23 -101.82 -119.95 -141.35 -155.62 -170.83 174.50 163.59 150.73 140.55
Specifications and information are subject to change without notice e-mail: sales@wj.com Web site: www.wj.com December 2004

▲Up To Search▲

Price & Availability of ECG055

	To Download ECG055 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .